+18 Sale to minors is prohibited.
-15% off Cannabis Seeds 🚚 Discreet shipping 24/48h 🎁 Free gift on orders over 30€ 🌱 3,000+ products 🔥 Weekly flash deals -15% off Cannabis Seeds 🚚 Discreet shipping 24/48h 🎁 Free gift on orders over 30€ 🌱 3,000+ products 🔥 Weekly flash deals

12 ton hydraulic pollen press

195,00 €

12 ton hydraulic pollen press: 25 × 32 × 45 cm steel frame, bottle jack with handle and a rectangular steel mould with two solid plates. It compacts pollen and resin into firm, even plates with no effort and consistent results.

- +
Guaranteed Safe Checkout

195,00 €

Discreet shipping 24/48h
Advice via WhatsApp
100% secure payment

12 ton pollen press: firm, even plates with no effort

After extraction, loose pollen and resin are hard to store and oxidise faster. The 12 ton pollen press compacts them into a firm, even plate with just a few pumps of the handle. Its hydraulic bottle jack delivers pressure no manual screw press can match: excess air and moisture are forced out and the resin is fully compacted, ready to store.

What’s included

  • Steel frame measuring 25 × 32 × 45 cm, stable and sturdy.
  • 12 ton hydraulic bottle jack with handle and release valve.
  • Rectangular steel mould: a 14 × 7 × 2.5 cm hollow plate that forms the mould, and two 13 × 6 × 1 cm solid plates that act as lids.

Why a hydraulic press

  • Far more pressure, far less effort: 12 tons in a few strokes of the handle.
  • Even plates: the pressure spreads equally across the whole mould and the plate comes out firm with no gaps.
  • Better storage: well-compacted resin exposes less surface to the air and oxidises more slowly.
  • Built to last: steel frame and mould designed for regular use.

Step-by-step instructions

  1. Warm the mould and plates in the oven at a low temperature or with a hair dryer. A warm mould helps the resin compact much better.
  2. Set up the mould: place one solid plate under the hollow plate, with baking paper in between.
  3. Load the material: fill the mould with dry pollen or resin, add another sheet of baking paper and put the second solid plate on top.
  4. Place it in the press: set the mould on the base of the frame with the hydraulic jack on top, and raise it until it meets the top of the frame.
  5. Press: pump the handle gradually until you feel resistance and hold the pressure for a few moments.
  6. Release and unmould: open the release valve to lower the jack, take the plates apart and remove the resin plate with the baking paper.

Tips for a good press

  • Always press dry material: damp pollen or bubble hash can go mouldy inside the plate.
  • Use baking paper between the resin and the plates: it peels off with no waste and the mould is easier to clean.
  • Build pressure gradually: the air escapes evenly and the plate is more uniform.
  • Work safely: set the press on a firm surface and keep your hands clear of the pressing area.

Specifications

Type Hydraulic pollen and resin press
Maximum pressure 12 tons
Operation Hydraulic bottle jack with handle and release valve
Frame dimensions 25 × 32 × 45 cm
Mould (hollow plate) 14 × 7 × 2.5 cm
Lids (solid plates) 13 × 6 × 1 cm, 2 units
Material Steel

Maintenance

Lubricate the ram and pump mechanism from time to time with oil made for hydraulic systems. Don’t open the pressure valve all the way, as the jack can lose oil, and don’t store the press upright with the jack fully lowered. Clean the mould and plates after each use.

Before you press: get the resin

This press is the last step of extraction. If you don’t have your resin yet, see our dry resin extraction range, with manual and electric pollinators, or ice resin extraction, with Secret Icer bags and washing machines. Find more models in our hash presses.

FAQ

What is a 12 ton pollen press for?

For compacting the pollen and resin from your extraction into a firm, even plate that’s easier to handle and store.

Do I need to warm the mould?

It isn’t essential, but it’s highly recommended: a mould warmed in the oven or with a hair dryer helps the resin compact better.

What size plate does it make?

The mould is 14 × 7 cm inside the hollow plate and 2.5 cm high. The final thickness depends on how much material you put in.

What maintenance does it need?

Very little: a drop of hydraulic oil on the ram and pump now and then, never opening the valve all the way, and cleaning the mould after each use.

Free shipping across Europe on orders over 100 €. Orders are packed within 48 hours and shipped in discreet, unbranded packaging.

Product intended for compacting resin obtained from plant material from your own garden. Sale to adults over 18 only. Please respect the laws in force in your country.

Weight 10 kg

Reviews

There are no reviews yet.

Be the first to review “12 ton hydraulic pollen press”

Your email address will not be published. Required fields are marked *

Scroll to Top
Logo Themariashop
Privacy Overview

This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.